翻译制袋机说明书

直接由翻译软件翻译过来的就算了。希望能够专业一点

1.冲孔装置打穿薄膜所需要的时间，设置值越小冲孔越快 2.每一批的制袋数量，例如设置为100，当计数值到达100只时计数自动归零，计批值则自动加1 3.色袋时在根据实际设置长度的基础上提前此范围检测色标，如果在送完实际长度仍未检测到色标则再继续延长此范围检测色标，仍检测不到色标则报警1次，连续报警3次主机自动停止，工作状态信息会显示光电错位请调整。 4.定型装置为选配装置，设置时间越长，定型装置封压薄膜的时间也越久，设置为“0”时定型关闭。 5.送料伺服马达的脉冲当量 6.当一批数量满时，机器停止并开始倒计时，到达所设置的时间机器又会自动启动，当设置为“0”时就算批满后机器也不会停止并继续工作 7.按此键会弹出密码键盘，输入正确的密码后确认可以进入特殊参数设置画面，初始密码为33333333 8.张口系数是指在切刀上，下一个时间周期内送料所用时间的千分比 9.步进马达或伺服马达手动调速/自动调速切换按钮 10.主机点动速度设置：数值越大速度越高 11.点此按钮主机运转一周，切刀自动停止在最高位置 12.设置批满停机时间后，当计数值到达时自动弹出此画面，并倒计时，时间满后自动返回到工作画面。 13.弹出批满画面后如按此按钮，机器立刻停止工作并返回到工作画面。

. Punching device punch through the time required for film, set the value of the smaller punch faster 2. The number of each batch of bag, for example, is set to 100, when the count reached 100 when the count is automatically zero, namely, the value of approved will automatically add 13. color bag when set up according to the actual length of this range based on the early detection of color, if not detected, while stocks last actual length of the color will continue to extend the range of detection of this color is still not detected color marked the alarm a second consecutive three times the host alarm automatically stops, work status information will be displayed optical dislocation adjust. 4. Shaping device as matching devices, set-up time longer shaping device closure pressure the longer the time for films
, Is set to "0" shape when closed. 5. Feed servo motor pulse equivalent 6. When a group of the number of full, the machine stop and start the countdown reaches the set time machine will start automatically when set to "0" when the grant expires even if the machine will not stop and to continue to work 7. Click the keyboard button will pop up password, enter the correct password to enter a special parameter settings confirmation screen, the initial password is 333,333,338. mouth factor refers to the cutter, the next time cycle time spent feeding more than nine thousand points. stepper motor or servo motor speed manual / automatic speed control switch button 10. Host jog speed set
Home: the higher the value the greater the rate of 11. Click here button to the host operating week, the cutter automatically stops at the highest position of 12. To set down time after the grant expires, when the count reaches automatically pops up this screen, and the countdown time expires screen automatically returns to work. 13. Pop-up grant, such as here, after full screen button, the machine to stop work immediately and return to work screen.