谁能帮我把这些中文翻译成英文啊？？

故障	原因分析	排除方法
仪表常加温	•固态继电器短路 •仪表OUT灯常亮	•更换固态继电器 •按出厂数据重新设置
仪表不加温	•固态继电器开路 •热电偶坏 •加热体开路	1.更换固态继电器 2.更换热电偶 3.更换加热体
机器运转后步进电机或伺服电机不送料	1.未接收到送料信号 2.可编程控制器没有输出 3.驱动器故障	1.调整送料传感器 2.更换 3.检查、更换
制袋长度不一致	•拉料辊压力不够 •步进电机运转不正常	1.加大压力 2.调整薄膜张力
采用色袋时自动报警停机	1.袋长设定与实际长度没有定 好 2.光电头距离没有调整好 3.光电头灵敏度没有调整好 4.光电头极性没有设定正确	1.调整制袋长度 2.调整感应距离 3.调整灵敏度 4.设定光电头极性
放料电机常放料或不放料	•放料传感器坏 •调速板坏 •接线松脱	•更换传感器 •更换调速板 •检查接线
启动后机器不转	•变频器无电源 •可编程无输出 •变频器参数设置错误	•检查变频器电源 •更换可编程 •重新设置变频器参数
送料料子与切刀碰或不能送出	1．送料太早	1．调整送料传感器
停机停不到高位或停机后机器还在运转	•高位传感器位置不准 •无高位信号	1.调整高位传感器 2.更换传感器
步进（伺服）电机声音异常或不转	1.步进电机缺相（伺服相位接错） 2.驱动器故障	1.检查步进（伺服）电机 2.检查、更换驱动器
输送电机常转或不转	•调速板坏 •接线松脱	1.更换调速板 2.检查接线

Failure Analysis Remedy
Instrumentation often short-circuit heating • Solid State Relays • Instrument OUT light Always • Solid State Relays • replacement of data by the factory reset
Instrument does not heat • Solid State Relay Thermocouple bad • Open • Open a heated body. Replace the solid-state relay 2. Replace the thermocouple 3. Replacement heater
After the machine running stepper motors or servo motors do not send material 1. Did not receive the feed signal 2. Programmable logic controller does not output 3. A drive failure. Adjustment of feeding sensor 2. To replace 3. Inspection, replacement
Bag length discrepancies • pull roller pressure is not enough • the inadequate functioning of a stepper motor. Increase the pressure 2. Adjustment of film tension
Use of color bag automatically when an alarm stop. Bag length setting does not set well with the actual length of the two. Optoelectronic not adjusted well from the first three. Photoelectric sensitivity not adjusted well the first four. Optoelectronic first polarity is not set correctly 1. Adjustment Bag length 2. adjustment of sensing distance of 3. adjust the sensitivity of four. set the optical head polarity
Electrical discharge and hold regular leak or a bad sensor materials • leak • Speed board or bad wiring loose • • • replace the speed sensor replacement board • Check wiring
Starts the machine does not turn • No power converter • Programmable output • inverter parameter settings without error • checks • replacement of the power inverter to reset the inverter parameters programmable •
The feed material will not be sent with the cutter, or a collision. Feeding too early one. Adjust the feed sensor
Down to stop or shut down after less than a high machine is still running high sensor location • • No high-signal 1 are not allowed to. Adjusted high of sensor 2. Replace the sensor
Step (servo) motor sounds abnormal or not to switch 1. Stepper motor missing phase (phase servo-access error) 2. A drive failure. Inspections step (servo) motor 2. Check and replaced the drive
Turning conveyor motor speed control board or not to switch • Bad • wiring loose one. Replace the speed control board 2. Check the wiring

Failure Analysis Remedy

Instrumentation often short-circuit heating • Solid State Relays • Instrument OUT light Always • Solid State Relays • replacement of data by the factory reset

Instrument does not heat • Solid State Relay Thermocouple bad • Open • Open a heated body. Replace the solid-state relay 2. Replace the thermocouple 3. Replacement heater

After the machine running stepper motors or servo motors do not send material 1. Did not receive the feed signal 2. Programmable logic controller does not output 3. A drive failure. Adjustment of feeding sensor 2. To replace 3. Inspection, replacement

Bag length discrepancies • pull roller pressure is not enough • the inadequate functioning of a stepper motor. Increase the pressure 2. Adjustment of film tension

Use of color bag automatically when an alarm stop. Bag length setting does not set well with the actual length of the two. Optoelectronic not adjusted well from the first three. Photoelectric sensitivity not adjusted well the first four. Optoelectronic first polarity is not set correctly 1. Adjustment Bag length 2. adjustment of sensing distance of 3. adjust the sensitivity of four. set the optical head polarity

Electrical discharge and hold regular leak or a bad sensor materials • leak • Speed board or bad wiring loose • • • replace the speed sensor replacement board • Check wiring

Starts the machine does not turn • No power converter • Programmable output • inverter parameter settings without error • checks • replacement of the power inverter to reset the inverter parameters programmable •

The feed material will not be sent with the cutter, or a collision. Feeding too early one. Adjust the feed sensor

Down to stop or shut down after less than a high machine is still running high sensor location • • No high-signal 1 are not allowed to. Adjusted high of sensor 2. Replace the sensor

Step (servo) motor sounds abnormal or not to switch 1. Stepper motor missing phase (phase servo-access error) 2. A drive failure. Inspections step (servo) motor 2. Check and replaced the drive

Turning conveyor motor speed control board or not to switch • Bad • wiring loose one. Replace the speed control board 2. Check the wiring